PrimoChill Vue - Computer WaterCooling Coolant, Visual Flow, Solid/Non-Transparent, Full Protection, PrimoPrep Included, Proudly Made in the USA (32oz/.9L) - Yellow

Awesome color dont understand why people complain so much about it it definitely requires maintaining but works and looks awesome

A lot of reviews on here are going to make you want to avoid this fluid. I don’t doubt that people have trouble with this fluid but I believe that if the proper preparation is done you will have a good experience with it. Make sure to follow the instructions and use the primo prep that comes with the bottle. Is the prep extensive and tedious? Yes. Do you have to change the fluid every 6 months? Yes Is this a difficult coolant to use? It can be. But the results are worth it if you enjoy the look My preparation for running this fluid was completely 1.draining my system of all previous coolant 2. Inspecting block fins for any clogs or blockages(any existing clogs or blocks will cause problems) 3 flushing with distilled water till old coolant is completely flushed. 4. Running primochills “system reboot” for 24 hours 5 flushing system with distilled water untill clear with no foam. (this process takes a while as system reboot creates a lot of hard to remove foam. 6. Running the included primo prep solution to loop and running for 72 hours. 7. Flushing primo prep completely out of loop with distilled water and running the clean distilled water for an hour before draining. 8. Drain distilled water and hook up a wet vac to drain valve to completely suck out and dry all water still in loop. 9. Add primo prep into loop. After this you want to go into bios and set a custom curve for your water pump. Make sure that the pump runs at only about 2000 rpm untill your cpu reaches temps above 50c This ensures that the fluid doesn’t get pushed through the system with too much pressure which can cause it to breakdown quicker and shorten the lifespan. This also allows for a better looking flow. Lastly as you run this fluid just keep an eye out for clogs and monitor your flow. I actually received lower temperatures with this coolant than the opaque fluid I was running prior. If you are meticulous with your prep and have good patience then this coolant is for you, if you are impatient and just want to throw it into your loop then don’t buy. Overall I think it’s a great beautiful looking product if you are willing to go through the prep and think it’s worth it. I certainly do On premochills website you can find all the information and warning about the fluid, they are very transparent with the difficulty of it and idk why people are bashing them saying they’ve been misled. Thanks for reading, hope this helps

Purchased this liquid for a high end build for a closed waterloop system in a ThermaltakeP90 case. At first, the liquid looks great. After only having it for a few months, i noticed that it started to build up muck on the fins of the GPU water block. So, flushed the liquid out, (the very expensive liquid i might add), and flushed it with distilled water. After 2 flushes, still had residue. Contacted support, they did nothing about it. SO i decided to buy their cleaning solution. Ran that in the loop for 3-4 days, STILL the build up was left in the tubes, the GPU and CPU waterblock. And the foaming in the pump, left fog on the glass that can not be removed at all. Thats not including the build up inside the pump just like all the other components. All in all, the liquid looks incredible, for a few weeks. Then, you start to realize, Its absolute garbage. It is going to ruin all the expensive water block components you purchase for your computer. Be aware, and stay very far away from this liquid. You will hate yourself later if you dont heed this review as a warning. and the manufacturer will do nothing about it.

I did a test run for 6 months, with a clean rad, used the primo prep, etc. I have a d5 non pwm pump by thermaltake, on medium setting. It lost its true color, left a very little bit of gunk. Its perfect for a show/asthetic build but not for a performance build. You will need to do a mentainence every 6 months or so. Overall if you are not going to keep everything in check and do maintenance its not for you.

The coolant works good, looks good. Prep fluid vs. coolant was about 4 degrees cooler. You can see the turbulent flow well, especially in the reservoir. Flow looks linear in the tubes, which is what you want, but swirls nicely in the tank and in my front flow wheel. I followed directions which require a 72hr+ prep time with loop prep. You then have to drain your whole system and then refill. It is annoying that it is not really disclosed until it arrives that you have to wait that long to use it. Make sure you can drain your system fully to swap out with the product once the prep of 3+ days is over. -1 stars for that one... would have been nice if it was more UV reactive but it's visible enough without that.

The PrimoChill Vue Pre-Mix (32oz) has been a fantastic addition to my computer’s water-cooling setup. First and foremost, the color is absolutely stunning—it adds an incredible visual appeal to the system that stands out beautifully. Beyond aesthetics, the cooling properties have been nothing short of impressive. It performs consistently and keeps my setup running smoothly, even under heavy loads. For anyone looking to combine style and performance in their water-cooling loop, the PrimoChill Vue Pre-Mix delivers on both fronts. Highly recommended!

It looks cool for the first few weeks. But the color started to settle in the blocks and pump leaving the color in chucks in the blocks. It will eventually leave you with a clear fluid after all the color settles out of it. I was expecting at least a few months for 40$

This coolant is absolutely something you should experience in your build for yourself. I haven't used Mayhem but I've used just clear or solid colors and after a day or so there boring no matter how vibrant the color you use this. This constant state of motion, lava lampish effect and after 6 months it still has the moving properties. I've broken my components down after a few months and there was some minor gunk in the jet plates but cleaned easily and left no discoloration in my rigid tube or acrylic waterblock. Next time just give this a try at least once .. I fully endorse